// ----------------------------------------------------------------------------
// Rotary Encoder Driver with Acceleration
// Supports Click, DoubleClick, Long Click
//
// (c) 2010 karl@pitrich.com
// (c) 2014 karl@pitrich.com
// 
// Timer-based rotary encoder logic by Peter Dannegger
// http://www.mikrocontroller.net/articles/Drehgeber
// ----------------------------------------------------------------------------

#include "ClickEncoder.h"

// ----------------------------------------------------------------------------
// Button configuration (values for 1ms timer service calls)
//
#define ENC_BUTTONINTERVAL    10  // check button every x milliseconds, also debouce time
#define ENC_DOUBLECLICKTIME  600  // second click within 600ms
#define ENC_HOLDTIME        1200  // report held button after 1.2s

// ----------------------------------------------------------------------------
// Acceleration configuration (for 1000Hz calls to ::service())
//
#define ENC_ACCEL_TOP      3072   // max. acceleration: *12 (val >> 8)
#define ENC_ACCEL_INC        25
#define ENC_ACCEL_DEC         2

// ----------------------------------------------------------------------------

#if ENC_DECODER != ENC_NORMAL
#  ifdef ENC_HALFSTEP
     // decoding table for hardware with flaky notch (half resolution)
     const int8_t ClickEncoder::table[16] __attribute__((__progmem__)) = { 
       0, 0, -1, 0, 0, 0, 0, 1, 1, 0, 0, 0, 0, -1, 0, 0 
     };    
#  else
     // decoding table for normal hardware
     const int8_t ClickEncoder::table[16] __attribute__((__progmem__)) = { 
       0, 1, -1, 0, -1, 0, 0, 1, 1, 0, 0, -1, 0, -1, 1, 0 
     };    
#  endif
#endif

// ----------------------------------------------------------------------------

ClickEncoder::ClickEncoder(uint8_t A, uint8_t B, uint8_t BTN, uint8_t stepsPerNotch, bool active)
  : doubleClickEnabled(true), accelerationEnabled(true),
    delta(0), last(0), acceleration(0),
    button(Open), steps(stepsPerNotch),
    pinA(A), pinB(B), pinBTN(BTN), pinsActive(active)
{
  uint8_t configType = (pinsActive == LOW) ? INPUT_PULLUP : INPUT;
  pinMode(pinA, configType);
  pinMode(pinB, configType);
  pinMode(pinBTN, configType);
  
  if (digitalRead(pinA) == pinsActive) {
    last = 3;
  }

  if (digitalRead(pinB) == pinsActive) {
    last ^=1;
  }
}

// ----------------------------------------------------------------------------
// call this every 1 millisecond via timer ISR
//
void ClickEncoder::service(void)
{
  bool moved = false;
  unsigned long now = millis();

  if (accelerationEnabled) { // decelerate every tick
    acceleration -= ENC_ACCEL_DEC;
    if (acceleration & 0x8000) { // handle overflow of MSB is set
      acceleration = 0;
    }
  }

#if ENC_DECODER == ENC_FLAKY
  last = (last = ENC_BUTTONINTERVAL) // checking button is sufficient every 10-30ms
  { 
    lastButtonCheck = now;
    
    if (digitalRead(pinBTN) == pinsActive) { // key is down
      keyDownTicks++;
      if (keyDownTicks > (ENC_HOLDTIME / ENC_BUTTONINTERVAL)) {
        button = Held;
      }
    }

    if (digitalRead(pinBTN) == !pinsActive) { // key is now up
      if (keyDownTicks /*> ENC_BUTTONINTERVAL*/) {
        if (button == Held) {
          button = Released;
          doubleClickTicks = 0;
        }
        else {
          #define ENC_SINGLECLICKONLY 1
          if (doubleClickTicks > ENC_SINGLECLICKONLY) {   // prevent trigger in single click mode
            if (doubleClickTicks < (ENC_DOUBLECLICKTIME / ENC_BUTTONINTERVAL)) {
              button = DoubleClicked;
              doubleClickTicks = 0;
            }
          }
          else {
            doubleClickTicks = (doubleClickEnabled) ? (ENC_DOUBLECLICKTIME / ENC_BUTTONINTERVAL) : ENC_SINGLECLICKONLY;
          }
        }
      }

      keyDownTicks = 0;
    }
  
    if (doubleClickTicks > 0) {
      doubleClickTicks--;
      if (--doubleClickTicks == 0) {
        button = Clicked;
      }
    }
  }
#endif // WITHOUT_BUTTON

}

// ----------------------------------------------------------------------------

int16_t ClickEncoder::getValue(void)
{
  int16_t val;
  
  cli();
  val = delta;

  if (steps == 2) delta = val & 1;
  else if (steps == 4) delta = val & 3;
  else delta = 0; // default to 1 step per notch

  sei();
  
  if (steps == 4) val >>= 2;
  if (steps == 2) val >>= 1;

  int16_t r = 0;
  int16_t accel = ((accelerationEnabled) ? (acceleration >> 8) : 0);

  if (val < 0) {
    r -= 1 + accel;
  }
  else if (val > 0) {
    r += 1 + accel;
  }

  return r;
}

// ----------------------------------------------------------------------------

#ifndef WITHOUT_BUTTON
ClickEncoder::Button ClickEncoder::getButton(void)
{
  ClickEncoder::Button ret = button;
  if (button != ClickEncoder::Held) {
    button = ClickEncoder::Open; // reset
  }
  return ret;
}
#endif